EVAP emissions — medium leak
P0442 Code: EVAP System Leak (Medium) Explained
P0442 stands for "Evaporative Emission System Leak Detected (Medium Leak)." It sits between the large leak of P0455 and the very small leak of P0456. The EVAP system captures fuel vapor from the tank so it does not escape into the air, and P0442 means the computer found a leak in that sealed system that is medium-sized.
A medium leak is often around 0.040 inch (about 1 mm) — big enough to fail the system test reliably but not as obvious as a loose gas cap. The cause is usually a cracked hose, a purge or vent valve that does not seal, or a worn gas cap seal. Like other EVAP codes, P0442 rarely affects drivability.
P0442 is an emissions code. It does not affect engine performance, fuel economy, or safety. The check engine light and a possible emissions test failure are the only practical effects, so there is no urgency.
You can keep driving normally. P0442 does not change how the car runs or its safety. Fix it to clear the light and pass emissions, but it is not a roadside situation.
P0442 symptoms you might notice
- Check engine light on
- No drivability problems in most cases
- Sometimes a faint fuel smell after refueling or when parked in the sun
- Failed emissions test
Common causes of P0442
Worn or loose gas cap
A cap with a dried, cracked, or worn seal can leak enough to set a medium-leak code even when it feels tight.
Cracked EVAP hose
A split in a rubber or plastic vapor line between the tank, canister, and engine is a common medium-leak source.
Purge valve not sealing
A purge valve that leaks when closed lets vapor escape and fails the EVAP test.
Vent valve leak
A vent valve that does not fully close during the leak test lets air in and trips P0442.
Cracked charcoal canister
A cracked canister housing can create a medium-sized leak that a smoke test will reveal.
Filler neck or O-ring wear
A worn filler neck O-ring or small rust spot can leak just enough to set a medium-leak code.
Before you buy parts
P0442 only tells you the EVAP system has a medium leak — not which part. The gas cap is the easiest thing to check, but cracked hoses and leaking valves are just as common. An EVAP smoke test pinpoints the leak so you replace only the bad part instead of guessing at the canister or valves.
What to check for P0442
- Remove the gas cap, inspect the seal, click it back on firmly, and clear the code to see if it returns.
- Have a shop run an EVAP smoke test. A medium leak is usually easy to find with smoke and shows the exact source.
- Inspect the EVAP hoses from the tank to the canister and engine for cracks, splits, and loose connections.
- Test the purge and vent valves for proper sealing. A valve that leaks when closed looks just like a hose leak.
- Check the filler neck and canister for cracks or worn seals if the cap, hoses, and valves are good.
Possible repairs for P0442
Replace the gas cap
A new OEM gas cap with a fresh seal fixes a share of P0442 codes inexpensively.
Replace a cracked EVAP hose
Swapping a split vapor line seals the medium leak.
Replace the purge valve
A purge valve that does not seal can be replaced to restore the system’s ability to hold vacuum.
Replace the vent valve
A vent valve that leaks during the test can be replaced to pass.
Repair the canister or filler neck
A cracked canister or worn filler neck O-ring is replaced when the cap, hoses, and valves are confirmed good.
Parts and tools that may help
Enter your year, make and model on the store's site to see parts that fit your car.
GarageGuide may earn a commission if you buy through these links, at no extra cost to you. Always check that a part fits your exact vehicle before buying.
P0442 frequently asked questions
Is P0442 the gas cap?
It can be. A worn or loose gas cap is a common cause. Check the seal, click the cap on firmly, and clear the code. If it returns, the leak is elsewhere in the EVAP system.
Can I drive with a P0442 code?
Yes. P0442 is an emissions code and does not affect how the car drives or its safety. You can keep driving while you arrange a repair.
How is a P0442 leak found?
An EVAP smoke test is the best tool. It pushes harmless smoke into the system so the leak is visible. This avoids replacing good parts by guessing.
Will P0442 fail an emissions test?
In most areas, yes. Any illuminated check engine light is an automatic emissions failure, even with no drivability problems.
What is the difference between P0442, P0455, and P0456?
All three are EVAP leaks of different sizes: P0455 is large, P0442 is medium, and P0456 is very small. The causes overlap, and a smoke test finds the source for any of them.